05-08 Halo Projector Fog Lights

This is not a DIRECT FIT. There will be minor modification to the Fogs and the Fog Light Housing. You will also need to cut and splice from the wiring harness that comes with the fog lights. Now. Lets get started:

What you will need:
Phillips-Head Screwdriver
Flat-Head Screwdriver
10mm Wrench
9005/9006 Plug and Play Connector
fbefb79eab6bfb10ab7d9a295f127af4  05-08 Halo Projector Fog Lights

1. Unhook the battery with the wrench.

2. Remove the grille.

6f96e8ed3c1fe17c1009d0b24598a5e0  05-08 Halo Projector Fog Lights

3. Remove the front bumper. 3 screws in the left and right fender wells.

4. Remove these 2 tabs with a flat-head screwdriver.

320166ea7e0544919df142d85a12f7fe  05-08 Halo Projector Fog Lights

And your bumper is off.

3d66cf98ce7fc3b9eac7552765a4ea5d  05-08 Halo Projector Fog Lights

I had to take it inside cause it was hella cold and the wind was blowing at 50MPH.

5. Cut the Male End to the Wiring Harness, leaving enough space in case you make a mistake.

7252dccdbda5520721f4b9c3a280b6ab  05-08 Halo Projector Fog Lights

6. Next, you want to take the connections from the harness that came with the fog lights and crimp the male/female connections together.

6fba4fefe5e736779c722e9ab1da8dcc  05-08 Halo Projector Fog Lights

e5a58d6b53caef528f9422e626ed46ff  05-08 Halo Projector Fog Lights

67fac81633cc468e4a35ebe2dde2901f  05-08 Halo Projector Fog Lights

7. Remove the clips from the “S” Lip Kit.

f878cc0dd0d36a4b56e0f814cf9aff8f  05-08 Halo Projector Fog Lights

8. And the screw.

70d4369f905002af34c046978ba32dfa  05-08 Halo Projector Fog Lights

9. Remove the Lip Kit.

b96c05f37055b3e8a5c07df5da19679d  05-08 Halo Projector Fog Lights

10. Remove the screw holding the Fog Light in place and it will come right out.

Here’s where the modifications begin.

11. Remove the stock screw and fog light mount from its place by using a flat-head screwdriver.

0df0e9710c16734b93a3b468d05d0c64  05-08 Halo Projector Fog Lights

12. In order to get the new fogs in place, I had to cut a little slit from the stock housing to be able to push the new fog housing through.

9a373019fff52784b74178d2eb7867d3  05-08 Halo Projector Fog Lights

As I pushed the fogs into place, I came upon my first problem.

8d4e9a03102f4600583b6fb4e6970b2b  05-08 Halo Projector Fog Lights

As you can see, the new fogs are wider than the stock fogs.

faf974d4128d505254f2bbaadd2ed75c  05-08 Halo Projector Fog Lights

I moved the fogs around a little, but they wouldn’t fit exactly. Thought it would be a problem, until I put the Lip Kit back on. It covered the space perfectly.

9e627ab5f3f9a4f634ef22fa33708806  05-08 Halo Projector Fog Lights

13. Replace the clips and screw holding the Lip Kit to the bumper. Also replace the Screw holding the Fog Lights into place.

14. Hook up your connections.

15. Re-Install the bumper. Assembly is the exact opposite of Removal.

16. Re-Install the grille.

17. And you are all set. Take a look. I know. I know. The car is dirty. I’ll wash it as soon as it gets warm around here.

2204d45e626671ec1e2c455f2a95ffea  05-08 Halo Projector Fog Lights

943265e61bf97a9f6409210d99022a50  05-08 Halo Projector Fog Lights

8922ad737e3bd910fd195d67b2d0ff59  05-08 Halo Projector Fog Lights

So, what do you think? I think they look great. They match the Head Lights and Grille perfectly. Total install time was a little over an hour. Might take you less if you are more familiar with your car than I am.

Both comments and pings are currently closed.

Comments are closed.